|
Tile fastening
devices and accessories are associated with nail down tiling applications.
These devices comprise many styles of hooks and clips. Some of these
devices are used in conjunction with the non-penetrating systems
for enhanced performance values. Tile clips are code required fasteners
under various conditions in many areas.
Always check with the
local building officials in your area or, contact the Wire Works
Inc., to verify your application.
|
|
|
|
|
|
|
|
Wire
Tile Hooks
Product #106.
Applicable to most styles of tiles. Applicable from 2/12 to 24/12.
Available in Copper, Brass, Stainless steel and H.D. Galvanized steel.
Applicable to California Title 24. (Nonferrous only) CAC Title 24
requires all tiles to be nose clipped on slopes of 7/12 and greater.
Applicable accessory to the #101 Twist wire, SST-1, and #104 Hook
& Loop.
Packaged in boxes of 1000 pieces. |
|
|
|
|
|
|
Wire
Tile Hooks are designed to secure the nose end of roofing tiles on
steep slopes and in areas designated as high wind zones.
The #106 Wire Tile Hook comes in two distinct styles,
(one for clay, one for concrete), and in two sizes,(for each style),
that preset the tiles designated headlap, (3 or 4 inches).
Tile Hooks are used on nail down, screwed, and
wired tiling applications. An adaptation of the Wire Tile Hook, is
the wire fastener known as the "Variable" Tile Hook.. This
version is designed with a fastener, (Nail, screw, wire), receiving
end and a long straight end of wire, that is used to bend back over
the tile. This is a very popular method for securing the nose ends
of an existing tile roof that may be experiencing wind related issues
and for tying in new tiles when replacing broken tiles.
|
 |
|
|
|
|
|
|
Flat
Metal Tile Hooks
Product #109.
Applicable to most styles of tile.
Applicable from 2/12 to 24/12.
Available in Copper, Brass, Stainless steel and H.D. Galvanized steel.
Applicable to California Title 24. (Nonferrous only). CAC Title 24
requires all tiles to be nose clipped on slopes of 7/12 and greater.
Applicable accessory to the #101
Twist wire and the SST-1.
Packaged in boxes of 1000 pieces.
|
|
|
|
The
strongest nose hook design currently available. The #109 Flat Metal
Tile Hook comes in two distinct styles,(one for clay, one for concrete)
that can preset the tiles designated headlap. This unique feature
is found in the design of the #109's base.
The base incorporates three fastener holes that
allow the hook to be pushed forward to create a longer headlap, or
pulled back, to shorten or adjust the headlap set of a course. This
base also extends beyond the nail hole of the tile, this reduces the
amount of lift that can occur with a wire device. The #109 has tested
to show greater resistance to uplift forces than any other style of
nose hook or side clipping device currently in use. |
|
|
|
|
|
|
|
Grip
Clips
Product #107
Applicable to most tiles.
Not applicable to two piece cap and pan tiles.
Available in Brass, Stainless steel, and H.D. Galvanized steel. Packaged
in boxes of 500 pieces.
|
|
|
|
Grip
Clips are manufactured from flat metal alloys into L shaped brackets
that are designed to clamp onto the water-channel side of roof tile
products.
The general purpose of the #107 Grip Clip is to
provide resistence against tile rotation or movement in a high wind
event. Grip Clips are primarily used with nails on wood deck substrates.
Grip Clips can be used with screws for additional
securement values. |
|
|
|
|
|
|
|
|
Hook
Nails
Product #108
Applicable to most styles of tiles.
Applicable from 2/12 to 24/12.
Available in Copper, Brass, Stainless steel and H.D. Galvanized steel.
Applicable to wooden substrates.
Applicable to California Title 24. Packaged in boxes of 1000 pieces.
|
|
|
|
The
Hook Nail is the ultimate nailed fastener for the installation of
tile. Manufactured from .135 diameter wire of various alloys, the
Hook Nail is the most effective wood deck fastener available. |
|
|
|
|
|
- The nail end is approximately 6 inches away
from the tile, this assures no accidental hammer to tile contact
when nailing.
- When specified with a hook , the headlap is
automatically set at the required measurement; i.e. 3 or 4 inches.
- If wind should create lift to the nose of
the tile, the hook will rise slightly with the tile, causing the
long shaft to bow downward to the deck, thus forcing the nail
end to stay into the deck.
- The fastener end is easily sealed with a
membrane compatible mastic
|
|
|
|
|
The #108 Hook Nail is the most
effective fastener for steep pitch designs, such as mansard roofs.
The Hook Nail is also used in high wind designated areas for securing
the first course of 2-piece cap and pan tiles. A version of this
fastener is also available without the hook. Known as the "No-Hook
Nail " Nail. The No-Hook Nail is a cost effective alternate
to standard nail and wire method.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Copper
and Stainless Steel Nails
Product #110
|
|
|
|
The
Wire Works Inc., manufactures a complete line of 300 series Stainless
Steel and copper roofing nails in both smooth and ring shanked styles.
Sizes are available from 7/8th of an inch to 6 inches in 1/4 inch
increments. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Slate
Hooks
Product # 111
Available in Copper, Brass, Stainless steel and black oxide finished
Galvanized
Steel. Packaged in boxes of 1000 pieces |
|
|
|
|
The
Wire Works Inc., manufactures a complete range of slate hook fasteners.
With headlap sizes from 2 to 4 inches. Slate hooks provide for the
installation of slates not pre-punched with fastener holes and allows
for the quick, secure replacement of broken slates. And when used
with any style of slate, slate hooks offer added protection from wind,
snow and ice. |
|
|
|
|
|
|
|
|
 |
|
|
|
|
